RADVision SCOPIA XT4000 Series Technické informace

Procházejte online nebo si stáhněte Technické informace pro Brány / ovladače RADVision SCOPIA XT4000 Series. RADVision SCOPIA XT4000 Series System information Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk

Shrnutí obsahu

Strany 1 - SCOPIA XT4000 Series

Administrator GuideVersion 3.0For Solution 7.7SCOPIA XT4000 Series

Strany 2

Figure 1-3 Using a NAT and Firewall Traversal ServerConfigure the traversal server as the XT Codec Unit gatekeeper and enable the H.460option. Configu

Strany 3 - Table of Contents

Figure 1-4 Using XT Series for NAT and Firewall TraversalThere are two possible setups in the GLAN1 and GLAN2 configuration (see Figure 1-4 onpage 7):

Strany 4

Supporting ISDN Connectivity The SCOPIA XT Series supports ISDN connectivity, allowing calls from endpoints to be routed tothe relevant conference u

Strany 5 - Deployment

This chapter details the ongoing maintenance tasks required by administrators for ongoing useof the SCOPIA XT Series. For information on configuring s

Strany 6

•For computers and laptops with a DVI out connector, connect the DVI cable to the DVI-Isocket of the XT Codec Unit and connect the other end of the ca

Strany 7

ProcedureStep 1Right-click on your computer desktop. The Display Properties page appears.Step 2Select Settings.Step 3Select one of the relevant resolu

Strany 8

We strongly recommend that you change the default credentials first time you access theSCOPIA XT Series remotely.Specific operational information on h

Strany 9

Table 2-2 Configuring remote management on SCOPIA XT SeriesField Name DescriptionWeb management Enables/disables Web access to SCOPIA XT Series.HTTPS

Strany 10

Figure 2-3 Logging into the SCOPIA XT Series web interfaceStep 3Enter the username and password.Step 4Select the web interface language from the Langu

Strany 11

Figure 2-4 Setting the XT Remote Control Unit CodeStep 3Enter the code in the Remote control code field.Step 4Select Save.Step 5On the XT Remote Contr

Strany 12 - Supporting ISDN Connectivity

© 2000-2012 RADVISION Ltd. All intellectual property rights in this publication are owned by RADVISION Ltd and areprotected by United States copyright

Strany 13 - Maintenance Tasks

How to Update the Software for SCOPIA XT Series This section describes how to upgrade the software running on the XT Codec Unit. NoteAny software

Strany 14

Before you beginDuring this procedure you need to enter the IP address and the subnet mask associated withthis IP address. Make sure you have this inf

Strany 15 - Procedure

Upgrading the Software Using a PC This section describes how to upgrade the software running on the XT Codec Unit from theSCOPIA XT Series web inter

Strany 16

Figure 2-7 Upgrading the firmware of the SCOPIA XT SeriesThe software is downloaded to the XT Codec Unit. You can view the progress on the SCOPIAXT Se

Strany 17

Figure 2-8 The USB ports on the rear panel of the SCOPIA XT SeriesThe upgrade procedure begins automatically.Step 3Follow the instructions displayed o

Strany 18

ProcedureStep 1Access the SCOPIA XT Series web interface.Step 2In the Administrator settings tab, select Utilities > Remote access > AT Commands

Strany 19

•Monitoring - SCOPIA iVIEW Management Suite can request identification and accesscapabilities from the endpoint.•Status traps - SCOPIA iVIEW Managemen

Strany 20

Field Name DescriptionSNMP management Enables/disables SNMP use.Administrator name Enter the name of the administrator in charge of managing theSCOPIA

Strany 21

Figure 2-11 Enabling importing and exporting configuration filesStep 3Set the fields as required.Field Name DescriptionEnable import Enable/disable im

Strany 22

This section covers troubleshooting problems that may occur when setting up and operatingthe SCOPIA XT Series.•Resolving Problems Connecting Calls ...

Strany 23

1Planning the Topology of the SCOPIA XT Series Deployment About the SCOPIA XT Series...

Strany 24 - Before you begin

SolutionMake sure the Do Not Disturb (DND) function is not enabled. DND is indicated by the iconin the top bar on the menu screens.ProblemCannot con

Strany 25

Resolving Problems with Audio ProblemI cannot hear audio after setting up the system.SolutionMake sure the monitor volume is not set to 0.SolutionMa

Strany 26

4.Select the Tx tone button to check the audio output. If the test is completedsuccessfully, the Done message is displayed. NoteIf the tone is ampli

Strany 27 - Management Suite

Step 6If it is necessary to further fine tune audio delay, perform these steps:a. Navigate to User settings > Diagnostics > Audio > Tests pag

Strany 28 - Additional Documentation

2.In the Administrator settings tab, select Calls > Video Quality > General.Figure 3-5 Configuring the lip sync settings3.Set the fields as desc

Strany 29 - Troubleshooting

Resolving Camera Issues ProblemCannot see the camera’s output after setting up.SolutionPress on the XT Remote Control Unit repeatedly to switch bet

Strany 30

Resolving IP Address Problems ProblemCannot configure the IP address.SolutionIf the icon for no network connection appears and the system displays

Strany 31 - Resolving Problems with Audio

Figure 3-8 Configuring IP address3.Enter the IP address.4.Select Next.5.Select Done.ProblemThe system does not make calls when IPv6 support is enabled

Strany 32

6.Select Save.Resolving Problems with PC Presentations ProblemI cannot send a presentation from my PC.SolutionMake sure the VGA/DVI cable is properl

Strany 33 - Resolving Lip Sync Problem

Retrieving Network Traffic Logs This procedure describes how to retrieve log files that provide information about networkstatus. For more informatio

Strany 34

Additional Documentation... 243Troubleshooting Resolving Problems Connectin

Strany 35 - Resolving Camera Issues

•eth1—for GLAN2•any—for both GLAN1 and GLAN2; in this case packets for both GLAN1 and GLAN2 arecollected into the same log file.Step 6Start retrieving

Strany 36 - Resolving IP Address Problems

Figure 3-10 Retrieving memory dump logsStep 3Select Create new log file.Step 4Wait for the system to create the log package file and display the link

Strany 37

NoteIf you need the system serial number, you can also look on the label at the back of the XTCodec Unit. ProcedureStep 1From the Main Menu, sele

Strany 38

www.radvision.comAbout RADVISIONRADVISION (NASDAQ: RVSN) is the industry’s leading provider of market-proven products and technologies for unifiedvisu

Strany 39

There are a number of ways that the SCOPIA XT Series can be deployed in a network,depending on its use as a room system endpoint, a conference hosting

Strany 40 - Retrieving Memory Dump Logs

The SCOPIA XT1000 and SCOPIA XT1200 share the same XT Codec Unit, but the SCOPIAXT1200 has a camera with higher quality optics. Both models support tw

Strany 41 - Viewing System Information

Table 1-1 Differences in features for models in the SCOPIA XT SeriesFeature SCOPIAXT1000PiccoloSCOPIA XT1000and SCOPIAXT1200SCOPIA XTTelepresenceSCOPI

Strany 42 - Contacting Support

Figure 1-1 SCOPIA XT Series as EndpointsPlanning NAT and Firewall Traversal with SCOPIA XT Series SCOPIA XT Series fully supports NAT and firewall t

Strany 43

Figure 1-2 Using an HTTP/STUN Server for NAT and Firewall TraversalThis approach works well in simple NAT and firewall traversal deployments, typicall

Komentáře k této Příručce

Žádné komentáře